NC530HS

Fully Automatic Band Saw NC530HS - Heavy duty, high speed, hydraulic, horizontal, metal cutting bandsaw with 20 H.P. and 2-5/8' blade.


PRODUCT DESCRIPTION

  • Capacity:  20” x 20” (530 x 530 mm) Rectangular, 20” (530 mm) Round
  • Blade:  2-5/8" x 21’ 10-1/2" x .063”  (37 x 1.6 x 6670 mm) Uses either bi-metal or carbide tip blade (TCT)
  • Heavy Duty Construction:  The saw frame is constructed of 3/4” plate stock with an 8” square tube running across its top to prevent deflection when the blade is put under tension.
  • Blade Tension:  Hydraulically controlled tension provides consistent square cutting accuracy. The Motion Detector will shut the machine off should a blade break or stall.
  • Speed Range:  49-393 SFPM (15-120 m/min) infinitely variable through a servo motor and heavy-duty transmission. The broad speed range allows for optimum cutting of a large spectrum of materials.
  • Rigid Dual Column:  rides on lineal ways providing optimal cutting performance with industry leading cutting accuracy.
  • Hydraulic Down Feed:  Feed rate and pressure can be controlled independently for fast, accurate cutting.  Cutting data is stored in the machine’s control and will automatically set feeds and speeds based on the material specs being cut .  The down feed also will automatically adjust itself to different cutting resistance as the blade moves downward through the material.
  • Hydraulic Shuttle Feed:  Length settings of 0 - 20” are accomplished by inputting the data into operator’s touch screen control.  The shuttle comes to positive stops at both ends of the index, assuring cutoff length accuracy, reducing material loss.  Repeatability is + .005 per index. The under slung shuttle features a 10 roller in feed table and a multi-index system.
  • Motors:  Blade Drive: 20 H.P. (15 kW). Hydraulic Pump Motor: 5 H.P. (3.7 kW). Coolant Pump Motor: 1/2 H.P. (375 kW).
  • The operator’s control panel is conveniently located on the right hand side of the machine and offers touch screen data input and a self diagnostic system. It also offers full control of all the machine features such as; vise clamping, piece counter, shuttle advance & retract, hydraulic clamping of the blade guides, coolant, work light and more.  The touch screen controls provides built in cutting data for a large variety of materials which will aid in the set up of each job to be run.
  • Automatic Positioned Moveable Guide Arm:  will position itself next to the material providing maximum support of the blade through the entire cutting operation.
  • Piece Counter:  The machine will stop the automatic cycle when a predetermined number of cuts have been reached.
  • Out-of-Stock Switch:  The machine will shut off automatically when material is no longer present in the rear vise jaws, allowing for truly automatic operation.
  •  Blade Guides:  The combination roller bearing and hydraulic clamping carbide blade guides with vibration dampening unit, reduce heat and blade stress providing longer blade life and accuracies of + .002 per inch of cut material.
  • Automatic Work Height with Fast Approach:  Work height is automatically set allowing the head to rise just enough to clear the workpiece, reducing cycle time and allowing for faster cutting performance.
  • Chip Brush:  Powered from the main drive shaft of the saw, the brush changes speed along with the blade to assure that chips are being removed from each gullet of the blade, improving cutting performance.
  • Full Stroking Hydraulic Vise Jaws:  The Front Vise jaws are split to reduce the remnant to as little as 4.3”.  The split vise jaws also help to reduce burrs left on the material and are ideal for bundle cutting.  Holding the workpiece on both sides of the blade reduces blade vibration, providing ore accurate cuts and longer blade life.  The Rear Vise Jaw Floats hydraulically to accommodate crooked stock assuring straight, accurate cuts.
  • Out-of Square Detector:  assures that you are always cutting within your predetermined tolerances.  This feature will shut the machine off automatically should machine begin cutting outside of those parameters.
  • LED Work Light:  Positioned directly over the work area to provide better illumination of the cutting area, the work light can be turned on and off independently from the operator’s control panel.
  • Zero Point Trim:  Provides automatic detection of front of work piece to eliminate the need for a reference cut saving time and material.

Other Standard Features: 

  • Table height 29-1/2"
  • Automatic Chip Conveyor
  • High Efficiency Transmission
  • Flushing Hose
  • HMI/PLC Controls
  • Machine Weight………………………………………………………………………………………..…................15,400 lbs
  • Hydraulic capacity………………………………………………………………………………………...……........18.5 gals.
  • Coolant capacity……………………………………………………………………………………………..…………21 gals.

 

SPECIFICATIONS

Capacity (Round) 1.25” (min.); 20” (max.) 30 mm (min.); 530 mm (max.)
Capacity (Square) 1.25” x ¾” (min.); 20” x 20” (max.) 30 x 10 mm (min.); 530 x 530 mm (max.)
Blade Speed 15-120 m/min
Blade Drive 20 H.P (15 kW)
Hydraulic Pump 5 H.P (3.7 kW)
Coolant Pump 1/2 HP (375 W)
Blade 2-5/8" x 21' 10-1/2" x 0.063 (Uses either bi-metal or carbide tip blade TCT)
Blade Tension Hydraulic
Machine Weight 15,400 lbs. (7,000 kg)
Table Height  29-1/2"